Hanging your wallpaper isn't hard when you have superior instructions to follow. Is it time to improve your home or office?

If you are new to wallpaper then take note of the kind of wallpaper you are attracted to when selecting. Depending on which kind you decide on, there may be some different installation methods. Pre-pasted wallpaper has a dry paste that is already attached to the back of the paper. This is initialized by using water, while unpasted wallpapers require a wet paste applied with installation. Typically, the installation method is the same although depending on which sort you use the instructions may vary.



Measure, cut, activate with H20 or paste and hang are the general instructions for installing wallpaper.

Wall Preparation

Your surface area and work area needs to be tidy and clear ahead of wallpaper installation. Clear away all wall fixtures and check that any electrical outlets are turned off. Remove any previous wallpaper paste or residue and wash the walls thoroughly with TSP before getting started.

Use a premixed universal primer for wallpaper to organize your wall. If you are applying unpasted wallpaper, priming the wall is important to facilitate easier removal.

Measure & Activate the Paper

The size of the wall is your very first measurement. Add four inches to this number and then trim your wallpaper. You need the paper to overlap the ceiling and the baseboard by approximately 2 inches.

Pro Tip: Allow for pattern match, via drop match, straight across or random.



If hanging unpasted wallpaper…

You can either apply the paste to the wall or paste the wallpaper backing. If you opt to paste the wall, apply it evenly and cover a portion for one wallpaper strip each time. When pasting the wallpaper, start in the centre and work out towards the edges while you evenly cover the wallpaper. Afterward, carefully fold the pasted sides of the moistened strip together with each other and allow them to rest for three minutes. This method is called booking.

Experiment to ascertain if you prefer pasting unpasted variations by applying the paste to the paper or even the wall. Make sure you only paste one region of the wall at one time when you are pasting the wall. If you are putting on paste to the wall, only paste one segment at a time. If you are employing the paste to the paper, put an even coating of paste on the wallpaper backing. Start in the centre of the wallpaper and work to the external edges. Slowly fold the moistened wallpaper strip and maneuver the pasted sides together so the booking process can take place. Allow the already folded wallpaper to sit in this way for three minutes.

When you use heavyweight wallpaper, as those unpasted varieties with cork, flock, or embroidery, opt for a clear stain-free pre-mixed paste heavyweight glue rather than light to medium weight.

When hanging pre-pasted wallpaper…

Have the patterned side in and the pasted side facing out once you cut your strip and roll it. Next, immerse the rolled strip for 30 seconds into tepid to warm water to activate the paste. Some prefer using a Wallpaper Hand Sprayer to employ a fine mist to stimulate the paste.

We really like this strategy and advocate spraying in long strokes the duration of the paper thoroughly moisten the back of the strip. Take extra care around the edges to obtain even watering. Next, fold up each end part of the moistened strip toward the center with pasted sides together. Don’t allow the edges to dry out by making sure they are aligned. Lastly, roll up the strip much like a loose newspaper and allow it to sit for 3 minutes to allow the paper to relax and the paste to become wholly activated.



Hanging your first strip

Move your strip to the wall after the booking process is completed after three minutes. Diligently unfold the strip and hang it up. Let the wallpaper overhang on the ceiling along with the baseboard. Eliminate any air bubbles using a smoothing brush or broad knife or a plastic smoother. Ensure that the piece has adequate exposure to the wall by pressing on the wallpaper. Be delicate so the wallpaper will not be distorted or stretched. Lightly flatten seams with a seam roller.

Proceeding to the second strip

When butting the second portion up to the first strip, position the second wallpaper sheet to the edge of the first. Firmly and efficiently press the wallpaper into place. Make sure to wash the ceiling and the baseboard after to get rid of any residual paste. Ideally, your joints should really be vertical with a tight fit. The paste has to be free from air bubbles for the best results.

Once you've installed three panels smoothly to the wall and eradicated excess paste, set aside a second to examine your work. Check the sheets for color and design uniformity. Carry on installing three panels in this way at a time. Matching styles or geometric designs may necessitate extra selvage pruning to create colour matching across seams. Tune in to your body and take rests when you detect your arms and eyes are getting tired. Wallpaper tasks take time and shouldn’t be rushed. Hanging your strips in this manner will allow you to achieve uniform results. Lastly, mindfully cut the excess trim along the ceiling and baseboards. It is suggested that you count on a guide and a razor knife to facilitate trimming without tearing.